XCSOURCE Metal J-Head Hot End 1.75mm Filament Direct Feed Extruder 0.4mm Nozzle Long-distance for RepRap 3D Printer TE561

Features:
Easy to assemble and use.
Comes with a 30mm Fan for cooling.
Can be fitted easily to a bowden extruder set-up thanks to the included pneumatic coupler.
Our hotend is capable of printing high temperature melting point plastics such as nylon and polycarbonate.

Specifications:
Material: Stainless Steel, PVC, Nylon
Voltage: 12V
Power: 40W
High accuracy: 1%
Resistance value at 25℃=100K
Wiring insulation: high temperature teflon/PTFE
Filament: 1.75mm
Nozzle: 0.4mm
Wiring length: 1 meter

Package includes:
1 x Metal J-head Hotend Assembly
1 x Cooling Fan

Product Features

  • Easy to assemble and use. Comes with a 30mm Fan for cooling.
  • Can be fitted easily to a bowden extruder set-up thanks to the included pneumatic coupler.
  • Our hotend is capable of printing high temperature melting point plastics such as nylon and polycarbonate.
  • Voltage: 12V; Power: 40W.
  • Filament: 1.75mm; Nozzle: 0.4mm.

Visit The Website For More Information…

What's Hot Today!

XCSOURCE 1.75mm 3D Printer Filament Detection Sensor Module Filament Run Out Pause Monitor for 3D Printer DIY Kit TE720

Normally, 3D printer DIY kit is not able to detect running out of filament, it will continue to print until printed file is finished even if the filament has already run out. This always leads to incomplete printing which will be wasting of your time and filament.

Features:
Newly designed smart module for detecting the status of the use of filament.
To check the filament is whether run out or not, it automatically stops the 3D Printer when the filament runs out, so you will have a chance to supplement the filament which makes sure you won’t print a incomplete printing.
Built-in wearable copper in the feed inlet and outlet to extend the life span.

Specifications:
Filament Size: 1.75mm
Mounting Hole Size: 3.5mm
Mounting Hole Distance: 20mm
Cable Length: 1m
Dimension: 38 x 30 x 12.7mm

Instruction:
1. When you are using a Lerdge brand motherboard: The green light on the motherboard will turn off when the filament runs out, the motherboard will stop printing until you supplement the filament and continue printing. (Please connect to the M-sensor Interface)
2. When you are using other brand motherboard: The Detection Module uses the level transition detection method. While there still have filament in the module, the detection port shows as high level; when there is no filament in the module, the detection port will transform to low level as “Filament Run Out Command” which will stop the printing, so you will have time to supplement the filament and continue printing.

Package Includes:
1 x Filament Detection Module
1 x Cable

Product Features

  • Normally, 3D printer DIY kit is not able to detect running out of filament, it will continue to print until printed file is finished even if the filament has already run out. This always leads to incomplete printing which will be wasting of your time and filament.
  • Newly designed smart module for detecting the status of the filament.
  • To check the filament is whether run out or not, it automatically stops the 3D Printer when the filament runs out, so you will have a chance to supplement the filament which makes sure you won’t print a incomplete printing.
  • Built-in wearable copper in the feed inlet and outlet to extend the life span.
  • Filament Size: 1.75mm

Click Here If You Need More Detailed Info…

What's Hot Today!

XCSOURCE 3D Printer Kit with RAMPS 1.4 Controller + Mega 2560 Board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display Controller with Adapter for Arduino TE621

12864 LCD Controller:
You can easy Connect it to your Ramps Board using the “Smart Adapter” included.
After Connecting this Panel to your Ramps you don’t need your pc any more, the Smart Controller Supplies Power for your SD card.
Further more all Actions like Calibration, Axes Movements can be Done by just using the Rotary Encoder on the Smart Controller.
Print your 3D Designs without PC, just with a G-Code Design Stored on the SD Card.

RAMPS 1.4:
Fully Assembled & Tested, No Soldering Required.
The Modular Design includes Plug in Stepper Drivers and Extruder Control Electronics on an Arduino MEGA Shield
For Easy Service, Part Replacement, Upgrade-Ability and Expansion.

Mega 2560 R3 Board:
Microcontroller: ATMEGA2560-16AU
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-20V
Digital I/O Pins: 54 (of which 15 provide PWM output)
Analog Input Pins: 16
DC Current per I/O Pin: 40 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 256 KB of which 8 KB used by bootloader
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16 MHz

A4988 Stepper Motor Driver:
Suitable for driving stepper motors below 8V ~ 35V 2A;
Very simple step direction control interface;
Five different stepping modes: full, half, 1/4, 1/8 and 1/16;
Adjustable potentiometer can adjust the maximum current output, can get better step rate;
Automatic current decay mode detection / selection;
High heat will result circuit cut, undervoltage lockout, crossover current protection;
Ground short-circuit protection and load short-circuit protection

Package Includes:
1 x 3D Printer Controller RAMPS 1.4 Board
1 x LCD12864 Intelligent controller
1 x Arduino-Compatible Mega 2560 R3
5 x A4988 StepStick Stepper Motor Driver Module with Heatsink
1 x Adapter
2 x FC flat cable
1 x USB Cable

Product Features

  • Brilliant 3D Printer Accessories Set meets most needs. Including RAMPS 1.4 Board, LCD12864, Arduino-Compatible Mega 2560 R3, A4988 StepStick Stepper Motor Module, and other accessories.
  • This full graphic Smart LCD12864 Intelligent controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display.
  • RAMPS (RepRap Arduino-compatible MEGA Pololu Shield) is designed to fit the entire electronics needed for a RepRap in one small controller for a lower cost and a smaller size.
  • Arduino-Compatible Mega 2560 R3 is fully compatible with the original Arduino MEGA 2560 R3, able to use all the Arduino open source platform to create or learn interactive objects.
  • A4988 StepStick Module is a complete microstepping motor driver with built-in translator for easy operation.

Click Here If You Need More Detailed Info…

What's Hot Today!

XCSOURCE J-Head Hotend 0.4mm Nozzle Metal 1.75mm Long Range For 3D Printer Makerbot Extruder BI092

Description:

Material: Metal

Thermistor: 100K NTC B 3950 ¡À1%

Heat tube: 12V 40W, 1m long

Nozzle size: 0.4mm

This 3D Printer J-head Hotend is applied for 1.75mm 3D Long-Distance Filament Bowder Extruder.

Package includes:

1 x J-head Hotend Long-Distance for 1.75mm Filament Extruder

Product Features

  • Material: Metal.
  • Thermistor:100K NTC B 3950¡À1%
  • Heat tube: 12V 40W, 1m long.
  • Nozzle size: 0.4mm.
  • This 3D Printer J-head Hotend is applied for 1.75mm 3D Long-Distance Filament Bowder Extruder.

Visit The Website For More Information…

What's Hot Today!