Description: Compatibility: compatible with all 1.75mm V6 E3D Makerbot 3D printer.
Notice: Small parts, keep away from children
Specification: 12V/40W heater,temperature can be up to 280°C（Long-term temperature: 240°C/ short-term temperature: 280°C） 12V high speed fan with shroud, radiating quickly One meter long PTFE/teflon tubing 4mm OD 2mm ID PC4-01 tube fitting Volcano heating block Outer thread : M6 M7 Nozzle throat outer diameter: 6mm Nozzle throat inner diameter: 4mm Teflon pipe inner diameter: 2mm Length of nozzle throat: 22.5mm Filament diameter : 1.75mm Extruder brass nozzle input diameter: 1.75mm Extruder brass nozzle output diameter: 0.3mm 0.4mm 0.5mm Volcano extruder nozzle output diameter: 0.6mm 0.8mm 1.0mm 1.2mm
Package including: 1 x all metal V6 hotend 12V/40W/1.75mm/0.4mm nozzle/ extruder 1 x 12V high speed fan with shroud 1 x One meter long PTFE/teflon tubing 4mm OD 2mm ID 1 x PC4-01 Tube Fitting 1 x 0.3mm nozzle print head 1 x 0.4mm nozzle print head 1 x 0.5mm nozzle print head 1 x 0.6mm volcano nozzle print head 1 x 0.8mm volcano nozzle print head 1 x 1.0mm volcano nozzle print head 1 x 1.2mm volcano nozzle print head 1 x volcano heating block 2 x teflon tube within 1.75mm stainless steel nozzle throat
Applicability & compatibility: compatible with all 1.75mm E3D V6 Makerbot 3D printer; NTC connector with terminal, easy to intall
Anti-leakage & anti-blocking design: extruder nozzle connect connect with the tube seamless, prevent print material from leaking or blocking
Heat resistant & ventilation: 12V/40W NTC heater, avoid NTC burn and break frequently, 304 stainless steel material nozzle throat and high quality resistor whose temperature can up to 280°C, 12V high speed fan, radiating quickly
Print the Widest Range of Materials Possible. High Temperature Peformance. With PTFE in hot regions of our HotEnd we can reach 260C with the supplied thermistor. By swapping a thermistor for a thermocouple (may require additional electronics) you can reach over 280C.
This not only allows you to print extremely high temperature materials like PP/ Polycarbonate and Nylons but also eliminates HotEnd meltdown failures associated . latest v6 hotend has a PTFE liner inside the hotend this liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating.
Our new HeaterBlock gives the fastest heat up times and the most responsive temperature control by clamping around the cartridge for maximum thermal contact. The new thermistor placement means you get the most accurate temperature readings with the fastest response. What this means for you the user is that you can go from 20C to 200C in just 65 seconds, temperature control is responsive enough that you can keep the hotend within 0.5C of your set temperature or less with ease.
Reduced Bulk and Z-Height. We’ve focused on cutting as much bulk from the E3Dv6 as possible. This means an overall length of just 72mm and significant reductions in bulk in the X/Y dimensions by using our new injection moulded fan duct.
Package Included: 1 x Metal J-Head hotend 1.75mm / 0.4mm nozzle / 12V/24V 40W Heater / NTC3950 Thermistor 1 x Heatsink shroud with 12V/24V 0.13A High Speed Fan 3010S 1 x One meter long bowden PTFE/teflon tubing 4mm OD 2mm ID 1 x Pneumatic Straight Fitting to connect to extruder cold end
RepRap 3D printer extruder hotend compatible with E3D V6 1.75mm / 0.4mm
12V/24V 40W heater, 12V/24V 013A high speed fan with shroud, NTC 3950 pre-wired thermistor
E3D-v6: Smaller – Easier – Higher Performance.
High Temperature Peformance.
Easy No-Solder, No-Tape, No-Adhesive assembly and maintenance.