BIQU MKS-BASE V1.4 Plate Controller Board for 3D Printer Ramps 1.4

Specifications:
A collection of all the functions on a single board to solve the complicated interfaces Ramps1.4 combination, problem-prone fault
Using high-quality MOSFET tube heat better
Control panel and can be connected directly Ramps1.4,2004LCD 12864LCD control panel
Net Weight:80g
Dimension:110*90mm

Note:
Before powering up again confirm whether the positive and negative reversed, if the user is due to reverse power and burn, and we do not guarantee such problems
Do not plug in case of power motor drive easily lead to burn; do not adjust the current in the motor is running. The correct approach is to first disconnect the power, unplug the motor, and then re-power, adjust potentiometer, measure the voltage on the potentiometer until the measured voltage is the same as expected
MKS-BASE is to create customer base for R & D personnel Ramps1.4, Megatronics V2.0 and other open source motherboard problems especially developed to optimize the launch of a product, particularly suitable for mass production 3D printer manufacturers use as the main control board
Give full consideration to the stability, heat dissipation, ease of use issues through continuous printing reliability testing
If special needs can contact the owner with details
Supporting line can refer to: 2PIN, 3PIN, 4PIN
Could be directly connected 2004LCD or 12864LCD (remove the L-shaped adapter plate), due to the open-source design 12864LCD 2004LCD and only standardized EXP1 and EXP2 the PIN port on the horns insertion direction and there is no specific standard, so some non Makerbase production and 2004LCD 12864LCD may be inconsistent data line card port direction, in turn, need to plug to use

Package Included:
1* MKS-Base V1.4 3D Printer Controller Board
1* USB Cable

Note: The socket color is ramdon, please double confirm you do not mind before placing order.

Product Features

  • Using 4982 as a motor drive, and a 4988 performance fairly, but with SOP package, heat dissipation will be better
  • The circuit board with high-quality 4-layer, and made a special heat treatment optimization; ramps are 2 shelves
  • Using a dedicated power supply chip, support 12V-24V power input, the voltage converter chip Ramps solve the heating problem
  • Could accept 24V input, the same system power can heat the bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems
  • The firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4

Detailed Information available on our Homepage…

What's Hot Today!

KINGPRINT 3D Printer MKS Gen V1.4 Controller Board Mega 2560 R3 Motherboard RepRap Ramps1.4 Compatible with USB

-Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.
-Tthe firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.
– Can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can’t be sure to match all of stype of 12864LCD and 2004LCD )
– Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
-Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs.

Specification:

Type: MKS Gen V1.4 control board Mega 2560
Name: MKS Gen V1.4 control board
Weight: 118g
Application: 3D Printer Part
Weight: 118g

Package Included:

1* MKS Gen V1.4 Control Board

Product Features

  • Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of failure prone.
  • Replace the motor drive, drive and support 4988 8825 drive.
  • The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
  • Using high-quality MOSFET, and better heat dissipation.
  • Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.

Visit The Website For More Information…

What's Hot Today!

OSOYOO MKS Base V1.4 3D Printer kit with MKS Base V1.4 Controller board + 12864 Graphic LCD

Caution
1) If your computer can’t recognize the MKS Base 1.4 controller board, Please download and install the FT232 driver in your computer: www.osoyoo.com/driver/ftdi_ft232_drive.exe . We have test this driver on Window XP and Windows 7. If the driver we provide doesn’t work with your computer, please google the “FT232”
2) If you cannot get the Z-axis to move or move in right direction, Pls read carefully about Marlin firmware installation guid and learn more about the setup for Z-axis: http://www.osoyoo.com/?p=1399
3) If the 12864LCD don’t show anything, pls turn out a notch on the other side of the EXP1 and EXP2 connector on LCD to make it work, as EXP1 and EXP2 connectors on LCD are soldered wrong,

Specification for MKS BASS V1.4 3D printer board:
suitable for dual-Extrude printer
3x temperature ADC connectors for thermistors
4x PWM capable power mosfet outputs with voltage selector for MainPower.(Bed, Extruder0, Extruder1, Fans)
6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax
Support 12V-24V power input. the Max working currency is 15A.
It can accept 24V input. With the same power input, the MKS BASS V1.4 board can reduced the current of hotbed to 1/4 than ramps1.4, so it solve the MOS hotbed overheat problems.
The size of the board: 11×9(cm)

Specifications for 12864 LCD:
Using a large screen 12864LCD(3.2″), 128 characters x 64 lines;
SD card can support 8 GB.
12864 LCD plug on MKS BASS V1.4 3D printer board directly, pls follow our installation guide when you use the 12864LCD.

Package include:
1x MKS Base V1.4 3D Printer Controller Board
1x USB Cable
1 x 12864 LCD controller (SD card not included)
1x Connector
2x 30 cm cable(without original box)

Product Features

  • We have full tech support to assist you with MKS BASS V1.4 3D printer board, For more details and Marlin firmware installation guide, Pls go to the web: http://www.osoyoo.com/?p=1399
  • This MKS BASS V1.4 board is with USB Driver Chip FT232RL, Please install the FT232 driver in your computer before useing, The FT232 driver link: www.osoyoo.com/driver/ftdi_ft232_drive.exe
  • This MKS BASS V1.4 board is with simple interface as it is the combination of Arduino MEGA2560 + RAMPS1.4 + 5 x A4982 drivers. 4 layers PCB design of MKS BASS V1.4 board optimize heat dissipation. A4982 drivers is SOP on MKS BASS V1.4 board, and it is better heat dissipation than A4988 driver. This MKS BASS V1.4 board can be recoverable fuse for short-circuit protection
  • This MKS BASS V1.4 board with Arduino MEGA compatible Atmega2560 and FT232 processors can be compatible with all RAMPS class firmware
  • With the MKS Base V1.4 3D Printer kit, you can easy to control your 3D printer device. Firstly, 12864LCD With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing. Secondly, MKS BASS V1.4 board with the RepRapDiscount SmartController compatible pin header on board. It can connect 12864LCD directly

Click Here If You Need More Detailed Info…

What's Hot Today!

OSOYOO MKS Base V1.4 3D Printer kit with MKS Base V1.4 Controller board + 2.8″ TFT LCD Touch Screen

Caution
1) If your computer can’t recognize the MKS Base 1.4 controller board, Please download and install the FT232 driver in your computer: www.osoyoo.com/driver/ftdi_ft232_drive.exe. If the driver we provide doesn’t work with your computer, please google the “FT232”
2) If you cannot get the Z-axis to move or move in right direction, Pls read carefully about Marlin firmware installation guid and learn more about the setup for Z-axis: http://www.osoyoo.com/?p=1399

Specification for MKS BASS V1.4 3D printer board:
suitable for dual-Extrude printer
3x temperature ADC connectors for thermistors
4x PWM capable power mosfet outputs with voltage selector for MainPower.(Bed, Extruder0, Extruder1, Fans)
6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax
Support 12V-24V power input. the Max working currency is 15A.
It can accept 24V input. With the same power input, the MKS BASS V1.4 board can reduced the current of hotbed to 1/4 than ramps1.4, so it solve the MOS hotbed overheat problems.
The size of the board: 11×9(cm)

Specifications for 2.8 Inch Full Color LCD Touch Screen:
2.8 inch colorful touch screen LCD
Support U disk and SD card.
Support continual and easy software update.
Suitable for many main board such as Ramps1.4 and MKS Base V1.2 update version, MKS Gen, MKS Mini.
Support Marlin, Smoothieware and Repetier.
Support MKS Wifi module.

Package include:
1x MKS Base V1.4 Board
1x USB Cable
1 x 2.8 Inch Touch Screen (SD card not included) 1x Flat cable

Product Features

  • We have full tech support to assist you with MKS BASS V1.4 3D printer board, For more details and Marlin firmware installation guide, Pls go to the web: http://www.osoyoo.com/?p=1399
  • This MKS BASS V1.4 board is with simple interface as it is the combination of Arduino MEGA2560 + RAMPS1.4 + 5 x A4982 drivers. 4 layers PCB design of MKS BASS V1.4 board optimize heat dissipation. A4982 drivers is SOP on MKS BASS V1.4 board, and it is better heat dissipation than A4988 driver. This MKS BASS V1.4 board can be recoverable fuse for short-circuit protection
  • With the MKS Base V1.4 3D Printer kit, you can easy to control your 3D printer device. Firstly, 2.8 Inch Full Color LCD Touch Screen With a SD card slot and USB Disk Solot on back, put slicing file into the SD card and select the file on the LCD, then can be printing. Secondly, MKS BASS V1.4 board with the RepRapDiscount SmartController compatible pin header on board. It can connect 12864LCD directly
  • 2.8 Inch Full Color LCD Touch Screen doesn’t need additional 12V additional power when connecting with MKS Base V1.4,
  • 2.8 Inch Full Color LCD Touch Screen Support keep printing and saving outage function. Using this function, you should choose Pause action first before you breakout the power. When you open the power again, the printer can run from the situation before you breakout the power

Click Here If You Need More Detailed Info…

What's Hot Today!