Witbot MK10 M7 0.4mm Extruder Upgrade Stainless Steel Wear Resistant Nozzle for Makerbot RepRap 3D Printer (Pack of 5pcs)

Specifications:
Bore Diameter: 0.4mm
Size: 13mm * 9mm
Net Weight: 4g/pcs
Material: Stainless Steel

Package Included:
5*MK10 Stainless Steel Nozzle

Product Features

  • 100% brand new and high quality
  • This product is dedicated on MK10 Extruders
  • The nozzle material use the national standard copper
  • Compare with the non-national standard copper, it have obvious differences,our nozzle’s thermal conductive performance is better than the non-national standard copper
  • Hard coating improves service life and reduces down time

Click Here For More Information

HICTOP 3D Printer Self Leveling Upgrade Auto Leveling Sensor Bed Self Adjustment Inductive Proximity Sensor

Specififation: Supply Voltage: DC 6-36V
Output Current: 300mA

Package list: 1* 3D Printer Auto Bed Leveling Kit

Product Features

  • This Proximity sensor is very useful and inexpensive solution for automated heatbed level adjustment
  • It detects metal objects (aluminum print surface)within 4mm distance
  • Dimensions: 18*18*36mm

Visit The Website For More Information…

RepRap Champion All Metal Direct Drive Extruder DIY Upgrade Kit for RepRap 3D printer Prusa i3. Right version.

This kit can help you improve your print quality by getting rid of filament slippage. Aluminum doesn’t soften at printing temp like the plastic printed parts can, leading to less idler spring tension, filament slipping, bad prints.

IMPORTANT: right version.

Hardware is included in the kit, but you might also need additional screws to mount heatsink with fan, for an example.

Package contents:

1 x Aluminum main extruder body.
1 x Aluminum tension lever.
1 x Idler bearing for 1.75mm filament.
1 x Brass drive gear.
1 x High tension spring.
1 x Assembly screws

Product Features

  • Ready to use 1.75mm filament extruder
  • Extrusion diameter is 0.4mm
  • Low vertical profile, saves print volume
  • Inexpensive to maintain, cheap MK8 replacement nozzles

Visit The Website For More Information…

Geeetech 3D Printer Self Leveling Upgrade Auto Leveling Sensor


Specifications:
Voltage: 5V
Current: 15mA
Max. Current: 300mA
Cable length: 150mm
Net Weight: 10g
Shipping weight: 25g

Wiring
3-pin: Brown (-, GND), Red (+5V), Orange (control signal)
2-pin: Black (-, GND), White (Z min)

Package list

1 X 3DTouch Auto leveling sensor
1 X 3Pin Straight Pin
1 X 2Pin Straight Pin
2 X Screw & Nut & Washer
2 X Dupont Housing Shell 3Pin
2 X Dupont Housing Shell 2Pin
3 X Dupont Housing Shell 1Pin
14 X Dupont Terminal
1 X 10KΩ 1/8W Resistor

Operate condition
3DTouch can be operated in the following condition.
One I/O for control (PWM or Software PWM)
One I/O for Z min (Z Probe)
GND and +5V power

Caution
Additional power supply will be needed in case your board does not supply enough amperage.
Electronic devices can be damaged or even destroyed if connected to wrong polarity. [wrong terminal connect to 5V(+) and GND(-)]
Pulling/pushing hard on the push-pin can damage 3DTouch and make it less accurate.
Fix push-pin with locking paint after reassembling or adjusting core.
Do not remove or deform elastic material attached on the push-pin.
Wiki: http://www.geeetech.com/wiki/index.php/3DTouch_Auto_Leveling_Sensor

Product Features

  • 1 Simple 3DTouch can be easily applied, Gathering information & firmware setting will be an easy task
  • 2 Smart Self-test: The push pin is operated three times to test when the power is on Alarm: The LED light blinks if a problem found on a self-test or on an operation
  • 3 High-precision 3DTouch’s Standard Deviation in repeatability is around 0.005mm
  • 4 Low power consumption even further drops joule heating, preventing from heat problem.
  • 5 wide Selection of Bed 3DTouch does not uses either optical, nor proximity (inductive/capacitive) sensor.

Visit The Website For More Information…