Kweiny MK10 Nozzle for 3D Printer Makerbot Parts and Extruder Cleaning Tools Kit | M7 Thread 0.4mm Brass Nozzle 5 Pieces and 2PCS Drill Bit for It

Notice:
1. After replace the nozzle, Please recalibrate the distance between nozzle and build plate to ensure the quality of print parts;
2. Don’t use the needle to clean until the nozzle is heated to above 200℃(392℉).You can twist the needle to make it easier to clean up;
3. Sharp parts, please keep away from children.

Specification of nozzle:
Compatibility: MK10 hotend M7 thread aluminum heater block;
Output diameter: 0.4mm;
Input diameter: 1.75mm/3mm;
Size: M7;
Material: Brass.

Specification of drill bit:
Compatibility: 0.4mm nozzle;
Size: 0.4mm*1PCS, 0.35mm*1PCS;
Length: 70mm/2.76in;
Material: Stainless steel SUS304.

Package include:
Brass nozzle: 5 pieces;
Nozzle cleaning drill bit: 2 pieces.

Product Features

  • Brass material advantage: The heat conductivity of brass is 7 times as high as that of stainless steel. MK10 hotend structure only allows filament to have little contact with the nozzle. The material of the nozzle must be brass to ensure filament’s temperature is the same as the thermistor, so it make the melt plastic more smooth. But the heat conductivity of stainless steel is so poor, it is unscientific and irrational used on MK10 nozzle.
  • Compatibility: Fit with MK10 hotend M7 thread aluminum heater block, such as FlashForge Creator Pro, FlashForge Creator X, FlashForge Dreamer, Dremel Idea, Builder PowerSpec 3D, Pro PowerSpec 3D X, Wanhao Duplicator 4S, Wanhao Duplicator 4X, Wanhao i3, etc.
  • Quantity and specification: M7 thread 0.4mm nozzle 5 pieces. 0.4mm Nozzle cleaning drill bit 2 pieces. For detailed dimensions, please refer to the drawings in the upper left.
  • Material: Nozzle is brass. Nozzle cleaning drill bit is stainless steel SUS304.
  • Durability: Nozzle cleaning drill bit can be used heaps of times, because of SUS304 stainless steel material. It will neither rust nor be broken, no matter how it is used.You only need one to solve all the same size nozzles blockage problems.

Visit The Website For More Information…

10 Pcs 5mm Male Thread 4mm/0.16 Push to Connect PC4-M5 For PTFE Tube 3D Printer Connector

Pneumatic fittings are used in pneumatic piping.

Features:
1. Easy to connect by inserting the tube it will automatically lock tight.
2. Easy to disconnect tube by one push on the blue cap.
3. Elliptical sleeve makes it possible to apply and remove the tube easily in confined space.

Applications:
One-touch joints used in pneumatic piping.
Used for a wide variety of modes to meet all needs.

Package include:
10x PC4-M5 Quick Fittings
10x Black Rubber Seal

Product Features

  • Item Name: Quick Fittings. Model: PC4-M5.
  • Material: Copper, Plastic. Color: Brass, Blue.
  • Thread Diameter: 5mm. Inner Diameter (Blue End): 4mm.
  • Total Size (Each): 19.8 x 10mm . Weight: 50g.
  • Package Content: 10 x PC4-M5 Quick Fittings. 10 x Black Rubber Seal.

Detailed Information available on our Homepage…

3D Printer M7 thread MK10 Nozzle Cleaning Kit 1.75MM filament .2mm .3mm .4mm .5mm .6mm .8mm 1.0mm Nozzles and De-clogging Bits + 3.5″ Pin-vise Poor Print Quality Solution

Kit includes: Nozzles/Bits/Pin-Vise

1) MK10 Nozzle for 1.75MM
Material: Brass
Filament inlet: 1.75mm
Fit for: Wanhao Dupicator D4/I3/Dremel and various Makerbot 3D Printers

Please verify that these are the nozzle for you printer. M7 thread MK10

(1 each)

.2mm

.3mm

.4mm

.5mm

.6mm

.8mm

1.0mm

2) Custom bit holding Pin-Vise

Fits 2.0mm and 3.75mm shank bits

3) Nozzle clearing drill bits:

(2 each) 0.2mm 0.3mm 0.4mm

(1each) 0.5mm 0.6mm 0.8mm 1.0mm

Cleaning Information:

These drill bits are of the highest quality you can find but are delicate by nature. Only with the bits can you clear clogs and clean out nozzles of any size. We have bits of larger sizes if you should need them.

The delicate nature of the bits means you must be very careful when using them. Do NOT apply side pressure. North/South movements only. You can clear a cold nozzle if done carefully, but it is HIGHLY recommended that you heat the nozzle first. You can leave it on the printer, or take it off. You can even heat it with a blow-torch after removing, but that will blacken the nozzle. Regardless, the nozzle should be fastened or clamped down if removed to avoid movement. Once you get the nozzle firmly set, use the pin-vise to insert the bit slowly. Spin the bit a few rotations and slowly pull it out. The nature of the bit curves will pull out any clogs and you are back in business!!

Product Features

  • Will clear nozzles and produce finer prints
  • Shipped in protective plastic case
  • M7 thread MK10 printer nozzles .2mm .3mm .4mm .5mm .6mm .8mm 1.0mm
  • De-clogging bits (2 each) .2mm .3mm .4mm (1 each) .5mm .6mm .8mm 1.0mm
  • 3.5″ comfortably held nozzle cleaning pin-vise tool

Click Here If You Need More Detailed Info…

REPKORD 3D Printer Nozzle Kit E3D Compatible M6 Thread Set 0.2mm, 0.25mm, 0.3mm, 0.4mm, 0.5mm, 0.6mm, 0.8mm, 1mm (Pack of 8)

The Repkord E3D compatible brass nozzle variety pack is a perfect upgrade to your 3D printer. Find the perfect nozzle to print at various speeds and levels of detail that make the most sense for your model. 8 Different nozzles are included: 0.2mm, 0.25mm, 0.3mm, 0.4mm, 0.5mm, 0.6mm, 0.8mm, and 1mm diameter. M6x1 threading for E3D and other compatible hot ends.

Product Features

  • 8 piece variety pack 3D printer nozzles
  • M6 x 1 thread
  • Brass
  • 0.2mm, 0.25mm, 0.3mm, 0.4mm, 0.5mm, 0.6mm, 0.8mm, and 1mm diameter
  • E3D V6, Volcano Compatible with All M6 threaded hot-ends

Click Here If You Need More Detailed Info…