Package Includes: 1 x RAMPS 1.4 Board 1 x Mega 2560 R3 Board 5 x Soldered A4988 Drivers 5 x Heat Sinks 1 x USB Cable 19 x Jumpers
RAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansion
Mega 2560 control board is an ATmega2560 as core micro-controller development board itself has 54 digital I/O input/output terminals (14 can be used as PWM outputs), 16 simulation than the input side, group 4 UARTs (hardware serial ports), 16 MHz crystal
RAMPS is designed to fit the entire electronics needed for a RepRap in one small controller for a lower cost and a smaller size.
With the boot-loader, download the program directly via USB without having to go through other external writer
After connecting this panel to your RAMPS, you don’t need your pc any more. The smart controller supplies power for your SD card. All actions like calibration, axes movements can be done by just using the rotary encoder on the smart controller
Item Descriptions: -100% Brand New and High Quality -Effective to reduce shock. -Suitable for 3D printer. -Anti vibration dampers for mostly applied stepper motors are available. -These energy- absorbing rubber mounts with a metal mounting face. -Stepper motors are affected by resonance. -Resonance is caused by parts vibrating in concert with each other, which can be lessened by fitting a stepper motor anti vibration damper.
Package: 3 x Shock Absorber For Nema17
Item Specifications: Size: 3.7cm x 3.7cm/1.5” x 1.5” Color: As shown Material: Rubber,Metal Brand:Unbranded/Generic
Effective to reduce shock.
Stepper motors are affected by resonance.
Anti vibration dampers for mostly applied stepper motors are available.
These energy- absorbing rubber mounts with a metal mounting face.
Resonance is caused by parts vibrating in concert with each other, which can be lessened by fitting a stepper motor anti vibration damper.
CNC Shield Board: Latest CNC Shield Version 3.0 for arduino GRBL 0.9 compatible 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 2 x End stops for each axis (6 in total) Coolant enable Compatible with A4988 or DRV8825 stepper driver Runs on 12-36V DC
DRV8825 Stepper Motor Driver: Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware)
Nema 17 Stepper motor Specification: Model No.:17HD48002H-22B Step Angle: 1.8 deg. Holding Torque: 59Ncm(84 oz.in) Rated Current/phase: 1.7A Frame Size: 41 x 41mm Body Length: 47mm Shaft Diameter: 5mm Shaft Length: 22mm Weight: 380g
Mechanical Endstop Connection description: Red line connect VCC (ramps of +) black wire connect the GND (ramps of -) Green Line connect SIGNAL (ramps in s) Tips: Under normal circumstances, the system must be configured to at least three mechanical switches. Advantage: Easy to install, the more common used styles Length of Cable: 70 cm
Package Contents: 1 x CNC Shield Board 1 x Kuman UNO R3 Board 4 x DRV8825 Stepper Motor Driver 4 x Aluminum heatsink w/ 3M tape backing 3 x Nema 17 stepper motor 1.7 A (with bracket and screw) 3 x Nema 17 Stepper Motor Mounting Bracket 12x M3 Screws for bracket of stepper motor 3 x Mechanical Switch Endstop 3 x 3Pin 70cm Cable 1 x 1.5m USB cable for R3 Board
Latest CH340G CNC Shield expansion board Version 3.0 for Arduino
Kuman UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable
4pcs DRV8825 Stepper Motor Driver with heat sinks
3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws
3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable