EasyULT 6 Pack Makerbot Designed Mechanical Endstop Kit Is For 3D Printer Makerbot Prusa Mendel RepRap CNC Arduino Mega 2560 1280

Connection Description:
Red line connecting VCC (ramps of +)
Connect the black wire GND (ramps of -)
Green Line connection SIGNAL (ramps in s)
High quality connection, using 22AWG wire
Inside of copper wire is very thick, can be resistant to current 2A or 300V voltage
A wide range of temperatures, up to 80 degrees
Tips: In normal circumstances, the system must be configured to three mechanical
Length of Cable: 70 cm
Quantity: 6 set

Product Features

  • Mechanical Endstop perfect for any 3D printer (Including Prusa Mendel i2, Prusa i3, MendelMax, Rostock etc…) also for use on CNC machines and other electronic applications.
  • Customized high quality connection, using 22AWG wire, copper wire inside is very thick, can be resistant to current 2A, 300V voltage. An insulating layer over a wide range of temperatures, up to 80 degrees.
  • Pros: Easy to install, the more common styles.
  • Not easy to pull off, easy to install
  • tips: Under normal circumstances, the system must be configured to at least three mechanical switches.

Click Here If You Need More Detailed Info…

8pcs GT2 16T Bore 5mm Timing Pulley+ 5 Meters Belt For RepRap Prusa Mendel 3D Printer GT16 Teeth

8pcs GT2 16T Bore 5mm Timing Pulley+ 5m Belt For RepRap Prusa Mendel 3D Printer

Product Features

  • GT2 Pulley : Teeth Number :16, Flange Double, Material Aluminium
  • Teeth Pitch 2mm , Diameter of Bore 5mm
  • Teeth Width 7.5mm(Very Suitable and good for 6mm synchronous belt)
  • GT2 Belt: Color Black, Pitch 2mm, Width 6mm
  • Material Fiber Reinforced Rubber, Length 5Meters

Detailed Information available on our Homepage…

Happisland Drill Bits for 3D Printer Nozzle Cleaning Makerbot Mendel Reprap Pack of 10PCS:0.2mm 0.3mm 0.4mm 0.5mm 0.6mm,Each 2 Pcs

Pack of 10 PCS:0.2mm 0.3mm 0.4mm 0.5mm 0.6mm,Each 2 Pcs

Product Features

  • Pack of 10 PCS:0.2mm 0.3mm 0.4mm 0.5mm 0.6mm,Each 2 Pcs
  • Conveniently colored silicone grip gasket for spinning bits by hand
  • Color is random
  • Note:Don’t use the drill to clean until the nozzle is heated to above 200 degrees
  • Any question,pls feel free to contact us.

Detailed Information available on our Homepage…

Witbot KFB2.0 controller board Ramps1.4/Mega2560 R3 a4988/DRV8825/TMC2100 Reprap Mendel Prusa I3 Kossel for 3D Printer

Specification:
Support: A4988, DRV8825, TMC2100.
Size: 10*10MM
Net Weight: 105g/pcs

Notice:
1.Don’t connect the waire of the mother board or change  various modules interface when electrified.
2.Pay attention to the Positive and negative of the wire.
3.Please check to determine whether the connection interface is correct, so as not to damage the motherboard before open telegram.
4.when in emergency occurs, please press the RESET button on the motherboard or disconnect.

Package Inlcuded:
 1* KFB2.0 controller board
 1* USB Cable

Product Features

  • 1, The power buck chip using XL1509 chip, high efficiency, stability. short circuit protection, 150KHz fixed switching frequency 2A current input 12 ~ 40V input voltage.the maximum support only 12V, supportA4988, DRV8825 and TMC2100
  • 2, USB serial chip using CH340T chip, the largest 2Mbps, communication Stable, to solve the streamlined version of the Windows driver can not be installed Problem, support for a full range of Windows, mac, liunx operating system
  • 3, The processor uses tamega2560 chip, 54 output to meet the various Output Interface
  • 4, Heatbed MOS tube with F8736 chip, the maximum 18A current
  • 5, tantalum capacitor filter acquisition temperature, anti-interference, more accurate

Click Here If You Need More Detailed Info…