HESAI RED MK2B PCB Heatbed Hot Plate with LED and Resistor and Cable for Reprap Mendel Prusa 3D Printer Support 12V 24V

Specification:

Power supply:12V or 24v

Laminate FR4 1.6+-0.15mm

Resistance between 1.0 -1.4 ohm(12V)or 3-5 ohm (24V)

Item Size:214mmx 214mm

Package List:

1× MK2B Heatbed with LED,Resistor And Cable

Product Features

  • It features a central mounting hole on the front side to allow for three point mounting
  • Copper plated holes
  • Compatible with any 3D printer that can accept the RAMPS MK2B version of heatbed
  • hese boards are all fully tested to confirm even heat distribution and correct resistance
  • Weld LED,Resistor and Cable

Visit The Website For More Information…

What's Hot Today!

HESAI 3D Printer Kit Smart Parts LCD 12864 Display Monitor Motherboard Blue Screen Module for RAMPS 1.4 Controller Control Panel

Specification:

This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included. After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.

Package List:

1x LCD 12864 Smart Controller

1x Smart Adapter

2x FC Cable

Product Features

  • Using a large screen 12864LCD
  • With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing
  • Product comes encoder parameter adjustment can be achieved, and the file selection print
  • Plug and play on the RAMPS, but need to modify the firmware to support

Click Here If You Need More Detailed Info…

What's Hot Today!

HESAI 3D Printer Kit Smart Parts RAMPS 1.4 Controller Control Panel LCD 2004 Module Display Monitor Motherboard Blue Screen

Description:

The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.4 board using “smart adapter” included.

This panel connect your RAMPS 1.4, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller. 3D design print without a computer, just use the G code design stored on the SD card.

Package List:

1x LCD 2004 Smart Controller

1x Smart Adapter

2x FC Cable

Product Features

  • Popular RepRap 3D Printer LCD Controller and SD Card Reader
  • Included adapter for RAMPS 1.4 board
  • Fully supported by Marlin firmware
  • With Smart LCD Controller you can print 3D designs without USB connection to your computer

Visit The Website For More Information…

What's Hot Today!

HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…

What's Hot Today!