Kweiny Heat Insulation Cotton and PTFE High Temp Tape for 3D Printer Makerbot Hotend Heater Block | 10PCS Cotton and A Roll of Tape for Extruder Parts Tool Kit

Notice:
1. After replace the nozzle, Please recalibrate the distance between nozzle and build plate to ensure the quality of print parts;
2. Please do not use flame to test their heat resistance, because the flame’s temperature is much higher than 300 degrees Celsius (572 Fahrenheit ).

Size:
Heat insulation cotton: Length 80mm/3.15in, width 20mm/0.78in, thickness 2mm;
PTFE high temp tape: Total length 10m/32.8ft, width 8mm, thickness 0.13mm

package including:
10PCS heat insulation cotton;
One Roll of PTFE High Temp Tape

Product Features

  • Compatibility: Matches all 3D print extruder heater block offered from E3D Makerbot, MK8 Makerbot RepRap , etc.
  • High temperature resistance: Both PTFE tape and heat insulation cotton, short term resistance to temperature 260 degrees Celsius (500 Fahrenheit ), long term resistance to temperature 300 degrees Celsius (572 Fahrenheit )
  • Function: Keep heater block temperature constant, so that improving the quality of the printed matter, save electricity and prolong the service life of heater and temp sensor
  • Use-method: You can cut cotton into the right size and hole according to your needs, then stick it firmly with PTFE tape. 5 sides of heater can be wrapped up in cotton, except the surface installed heater wire, but you just need to use 1 piece cotton. You can also use PTFE tape to stick any other parts on your 3D printer
  • Material: The heating insulation cotton is made from heat resistant ceramic fiber, the tape is made from PTFE

Visit The Website For More Information…

TOOGOO 3D Printer Heat Hot Bed Sticker Coordinate Printed 220x220mm Hot Bed Surface Sticker Black for 3D Printer Parts

* TOOGOO is a registered trademark. ONLY Authorized seller of TOOGOO can sell under TOOGOO listings.Our products will enhance your experience to unparalleled inspiration.
TOOGOO(R) 3D Printer Heat Hot Bed Sticker Coordinate Printed 220x220mm Hot Bed Surface Sticker Black for 3D Printer Parts
220x220mm 3D Printer Hot Bed Surface Sticker Accessory with 1: 1 Coordinate
Type: 3D printer hot bed platform sticker
Color: Black
Material: ABS
Size: approx. 220 X 220 X 1 mm/8.66 X 8.66 X 0.04 inch
Included:
1 x Hot Bed Coordinate Printed sticker
Note: Please check the size and fix carefully before applying the sticker.
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

Product Features

  • Suitable for PLA, ABS, HIPS, PETG, TPE filament, nylon, PC, RETT material.
  • Provides extra adhesive force between filament and heating board.
  • Effectively prevents deformation of ABS, PLA filament.
  • Compatible with ABS, PLA, HIPS and other type long filament.
  • Simple design, fast installation. Easy to use and apply. Dull polish treated surface, reusable 3D printer accessory.

Detailed Information available on our Homepage…

SIMPZIA Heat Bed Power Module General Add-on Hot Bed Power Module Expansion Board High Current Load Module Mos Tube Hotend Replacement with Cables for 3D Printer – 2 Pack

Heated Bed Power Module Features:
Based on powerful MOSFET HA210NO6
Dimensions: 70 x 45mm/ approx 2.76 x 1.77″
Distance between holes: 62.8 x 37.8mm/ approx 2.47 x 1.49″
Supply/Operating Voltage: 12V-50V (12-24VDC recommended)
Max Current: 25A (Enhance heat dissipation) safe for prolonged times. ensure active cooling of the heatsink.
This module is based on power MOSFET and will allow PID control of the heated bed (DC-DC Relays usually do not allow this)

Package Includes:
1 x Heated Bed Power Module.
1 x Connection cable for input signal
2 x Power cable

Note:
This module under the premise of normal cooling, it work stable under (Max) = 25A, the process of using the current not exceed 25A.

Product Features

  • APPLICATION: This high power module is a general add-on heated bed power expansion module for 3D printer. It can work with the Anet A8.
  • UNIQUE DESIGN: With unique snowflake heatsink design, it has a great cooling effect. The heat bed power module can be used in both Lerdge motherboard and other 3D printer motherboards.
  • 25A MAXIMUM CURRENT: This high power module helps your 3D printer equipped with the Lerdge controller board become even more powerful. The module can solve the current load problem when the heated bed power is too large. With this add-on module to board lead the maximum current up to 25A.
  • GOOD PROTECTION: When using heated bed 3D printer for 12V power supply which may cause excessive current during times, with this module, it can well protect the connectors on the controller board from burning.
  • PACKAGE INCLUDES: 2 x Heated bed power module (motherboard is not included) and 2 x Connection cable for input signal. BONUS: 4 x Power cables.

Detailed Information available on our Homepage…

Wisamic Clear Borosilicate Glass Heat Bed 200x200x3mm for 3D Printers Prusa, Monoprice Maker Select V2, Monoprice Maker Select Plus, etc

If you want to make your printing platform flat enough, ideal stuff is glass sheet. Tempered Silicon glass is rated for higher temperatures than normal sheet glass making it a better material for use as a heated bed. After cracking a few sheets of normal glass from rapidly cooling or heating, tempered glass will quell your frustrations.

Features:
* Borosilicate is a very high temperature glass. It has a melt temperature of about 800° C and a very low thermal expansion coefficient.
* Resistant to thermal shock compared to regular glass.
* Prepare a second plate and quickly switchplates when a model finishes printing. This significantly reduces printer idle time between prints.
* Reduces warping, however platform has to be properly leveled as is the case with any platform on a 3D printer.

Specification:
Material: 100% Borosilicate
Size: 200x200x3mm
Thickness: 3mm

Package content:
1 x 200x200x3x3mm Borosilicate Glass

Product Features

  • Precisely cut and tempered with high transparence. Resistance to scratch and thermal shock.
  • Conducts heat evenly across the build surface to ensure consistent temperature throughout the build surface.
  • High binding power when heating. Easy to separate the plastic parts when cooling.
  • Get you out of the trouble when plastic film decreased viscosity after a period of usage.
  • Specially designed to fit the 3D Printers Prusa, Monoprice Maker Select V2, Monoprice Maker Select Plus, etc

Visit The Website For More Information…