Professional 3D printer CNC Kit for arduino, kuman GRBL CNC Shield +UNO R3 Board + RAMPS 1.4 Mechanical Switch Endstop + DRV8825 A4988 GRBL Stepper Motor Driver with heat sink + Nema 17 Stepper Motor

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware)

Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles
Length of Cable: 70 cm

Package Contents:
1 x CNC Shield Board
1 x Kuman UNO R3 Board
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
12x M3 Screws for bracket of stepper motor
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
1 x 1.5m USB cable for R3 Board

Product Features

  • Latest CH340G CNC Shield expansion board Version 3.0 for Arduino
  • Kuman UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable
  • 4pcs DRV8825 Stepper Motor Driver with heat sinks
  • 3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws
  • 3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable

Click Here If You Need More Detailed Info…

What's Hot Today!

EasyULT 6 Pack Makerbot Designed Mechanical Endstop Kit Is For 3D Printer Makerbot Prusa Mendel RepRap CNC Arduino Mega 2560 1280

Connection Description:
Red line connecting VCC (ramps of +)
Connect the black wire GND (ramps of -)
Green Line connection SIGNAL (ramps in s)
High quality connection, using 22AWG wire
Inside of copper wire is very thick, can be resistant to current 2A or 300V voltage
A wide range of temperatures, up to 80 degrees
Tips: In normal circumstances, the system must be configured to three mechanical
Length of Cable: 70 cm
Quantity: 6 set

Product Features

  • Mechanical Endstop perfect for any 3D printer (Including Prusa Mendel i2, Prusa i3, MendelMax, Rostock etc…) also for use on CNC machines and other electronic applications.
  • Customized high quality connection, using 22AWG wire, copper wire inside is very thick, can be resistant to current 2A, 300V voltage. An insulating layer over a wide range of temperatures, up to 80 degrees.
  • Pros: Easy to install, the more common styles.
  • Not easy to pull off, easy to install
  • tips: Under normal circumstances, the system must be configured to at least three mechanical switches.

Click Here If You Need More Detailed Info…

What's Hot Today!

3D Printer parts Kossel Limit Switches Endstop with 1m/3-feet Long Cable

3-feet endstops with 1m cable

Product Features

  • 3-feet endstops with 1m cable

Visit The Website For More Information…

What's Hot Today!

Professional 3D printer CNC Kit for arduino, Kuman GRBL CNC Shield +UNO R3 Board + RAMPS 1.4 Mechanical Switch Endstop + DRV8825 A4988 GRBL Stepper Motor Driver with heat sink + Nema 17 Stepper Motor

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware)

Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles
Length of Cable: 70 cm

Package Contents:
1 x CNC Shield Board
1 x Kuman UNO R3 Board 
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
12x M3 Screws for bracket of stepper motor
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
1 x 1.5m USB cable for R3 Board

Product Features

  • Latest CH340G CNC Shield expansion board Version 3.0 for Arduino
  • Kuman UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable
  • 4pcs DRV8825 Stepper Motor Driver with heat sinks
  • 3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws
  • 3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable

Click Here If You Need More Detailed Info…

What's Hot Today!