Package Includes: 1 x RAMPS 1.4 Board 1 x Mega 2560 R3 Board 5 x Soldered A4988 Drivers 5 x Heat Sinks 1 x USB Cable 19 x Jumpers
RAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansion
Mega 2560 control board is an ATmega2560 as core micro-controller development board itself has 54 digital I/O input/output terminals (14 can be used as PWM outputs), 16 simulation than the input side, group 4 UARTs (hardware serial ports), 16 MHz crystal
RAMPS is designed to fit the entire electronics needed for a RepRap in one small controller for a lower cost and a smaller size.
With the boot-loader, download the program directly via USB without having to go through other external writer
After connecting this panel to your RAMPS, you don’t need your pc any more. The smart controller supplies power for your SD card. All actions like calibration, axes movements can be done by just using the rotary encoder on the smart controller
3D printer tool kit include 6 pieces 0.4 mm brass extruder nozzle print head, 6 pieces 30 mm length extruder 1.75 mm tube, 3 pieces 0.4 mm cleaning drill bits with 2 pieces hex drivers for MK8 3D printers
3D printer tool set: Anti-leakage and anti-blocking design, outer thread, you can install directly, compatible with most 1.75 mm PLA ABS 3D printer.
Specifications: Nozzle print head: Type: 0.4 mm extruder brass nozzle print head Color: golden Material: brass Oversize: 8 x 13 mm Input diameter: 1.75 mm Output diameter: 0.4 mm
Nozzle inputting tube: Type: nozzle throat Compatibility: 3D printer Outer thread: M6 Nozzle throat outer diameter: 6 mm Nozzle throat inner diameter: 4 mm Pipe inner diameter: 2 mm Length: 30 mm Filament diameter: 1.75 mm Material: stainless steel
Cleaning drill bits: Type: drill bit Bit diameter: 0.4 mm Bit length: 7 mm Shank length: 31 mm
Package include: 6 x 0.4 mm brass extruder nozzle print heads 6 x 30 mm length extruder 1.75 mm tube 3 x 0.4 mm cleaning drill bits 2 x Hex drivers
Attention: 1. Don’t use the drill to clean until the nozzle is heated to above 200 degrees. 2. Small parts, keep away from children.
Package include: 6 pieces 0.4 mm brass extruder nozzle print heads, 6 pieces 30 mm length extruder 1.75 mm tube, 3 pieces 0.4 mm extruder nozzle drill and 2 pieces hex drivers
Nozzle print head: made of brass material; Oversize: 8 x 13 mm; Input diameter: 1.75 mm; Output diameter: 0.4 mm
Nozzle inputting tube: made of stainless steel; inner diameter: 2 mm; Length: 30 mm; Outer thread: M6; Filament diameter: 1.75 mm
Cleaning drill bits: bit diameter: 0.4 mm; Bit length: 7 mm, the length of shank: 31 mm; Comes with a plastic box, convenient to store
Good compatibility: these 3D printer tool kit is compatible with most 1.75 mm PLA ABS 3D printer
Full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included. After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.
More information about Full Graphic LCD Smart Controller can be found in Full Graphic Smart Controller WIKI page
LCD 12864 Smart Controller Supported in Marlin Firmware.
– 1 x LCD Graphics controller. – 1 x Connection adapter. – 2 x connection cables.