BIQU TL-Smoother Kit Addon Module for Pattern Elimination Motor Filter Clipping Filter 3D Printer Motor Drivers Controller (1)

Package List:
1x TL-Smoother Addon Module
1x USB Cable

Product Features

  • The TL-Smoother is an addon module for 3D printer stepper motor drivers
  • The board provides flyback diodes (freewheeling diodes) for the motor outputs, so that they are also protected against induction voltages in the unpowered state of the driver
  • You will got smoother movement especially on the delta-style 3Dprinter under DVR8825 stepper drivers and A4988/2 drivers
  • Lower vibration lower noise smoother result
  • Dimension:40x30mm

Click Here If You Need More Detailed Info…

RAMPS 1.4 Controller + MEGA2560 R3 board + 5pcs Soldered A4988 Stepper Motor Drivers + 5pcs Heat Sinks + 19pcs Jumpers with USB Cable For Arduino RepRap 3D Printer Kit

Specifications:

RAMPS 1.4 Size: 9.1 x 5.9cm / 3.58 x 2.32″

Mega R3 2560 Size: 10.8 x 5.5cm / 4.25 x 2.16″

A4988 Color: Green

A4988 Quantity: 5pcs

Package Includes:
1 x RAMPS 1.4 Board
1 x Mega 2560 R3 Board
5 x Soldered A4988 Drivers
5 x Heat Sinks
1 x USB Cable
19 x Jumpers

Product Features

  • RAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansion
  • Mega 2560 control board is an ATmega2560 as core micro-controller development board itself has 54 digital I/O input/output terminals (14 can be used as PWM outputs), 16 simulation than the input side, group 4 UARTs (hardware serial ports), 16 MHz crystal
  • RAMPS is designed to fit the entire electronics needed for a RepRap in one small controller for a lower cost and a smaller size.
  • With the boot-loader, download the program directly via USB without having to go through other external writer
  • After connecting this panel to your RAMPS, you don’t need your pc any more. The smart controller supplies power for your SD card. All actions like calibration, axes movements can be done by just using the rotary encoder on the smart controller

Click Here If You Need More Detailed Info…

keyestudio MKS GEN 1.4 3D Printer controller Board /RAMPS 1.4 + Mega 2560 for Arduino (Black &Environmental-protection)

Intruduction
Keyestudio 3D MKS Gen V1.4 printer motherboard control board combines and improves the assets solution of the RAMPS 1.4 and Arduino Mega 2560 board on a fantastic single board.
Keyestudio 3D MKS Gen V1.4 printer motherboard control board is an optimal 3D printer controller solution for your Reprap 3D printer.

Features
Integrate 2560 and ramps1.4 in a board, to solve the complicated interfaces and broken problem of Ramps1.4 combination.
Replaceable motor driver, support 4988 driver and 8825 driver.
Circuit board using high-quality 4-layer board, and specially dealing with thermal optimization; ramps is a 2-layer board.
Using high-quality MOSFET tube, with better heat dissipation.
Using a dedicated power chip to support 12V-24V power input, to solve the problem of Ramps voltage converted into chip heating.
To accept 24V input, hot bed current can be reduced to 1/4 under the same system power, effectively solve the heating problem of hot bed MOS tube.
Firmware can use open-source firmware Marlin, and its configuration is exactly the same as ramps1.4, which can directly replace Ramps1.4.
Can directly connect to Ramps1.4,2004LCD control board and 12864LCD control board.
Set aside the motor pulse and direction output port, convenient to facilitate external high current to connect external high current (such as 2A, 5A) motor drive circuit.
Reserve the Servos, AUX-1, AUX-2 interfaces on Ramps1.4, providing three 5V output, three 12V output interface.
This board is an upgrade part of the MKS Gen V1.2 board, improving the performance of power protection and USB communication stability.

Package Included: 
1 x MKS-Gen V1.4 Controller 
1 x Usb Cable

Product Features

  • It gathered mega 2560 and ramps1.4 on a same board, hardware & software included, just scan the Qr code on the picture to get the wiki tutorial and software
  • Support 4988 driver and 8825 driver, Support 12V-24V power input; Firmware can use the same configuration as ramps1.4
  • Can directly connect to Ramps1.4,2004LCD control board and 12864LCD control board
  • Reserve the servos, AUX-1, AUX-2 interfaces on Ramps1.4, providing three 5V output, three 12V output interface
  • keyestudio MKS GEN 1.4 is manufactured from environmentally friendly materials and technologies, made function,voltage, current testing before packaging

Visit The Website For More Information…

COLLENCE 3D Printer Heating Controller 30A Heatbed MKS MOSFET for Extruder MOS Module

Usage:
1. Plug a power supply.
2. Connect to heated bed.
3. Connect digital control signal to GND, D8 of MKS Mini.
4. Connect to the heated bed signal on Ramps1.4 or MKS series controller boards.

Notics:
1. Only can choose 3 or 4 signal group.
2. Pay attention to polarity.

Package includes:
1 x Heating Controllor MOS Tube

Product Features

  • Each one has been done functional test.
  • Superior performance of MOSFET (Max 280A).
  • Can use for hot bed, output signal of Ramp1.4 and MKS series to control.
  • Can use digital signal of 5-24v to control.
  • Extra large heat sink , the maximum current can be up to 30A or more.

Detailed Information available on our Homepage…