TIANSE 0.4mm Drill Bits for 3D MakerBot Printer Nozzle Cleaning Kit, 5PCS

★Don’t use the drill to clean until the nozzle is heated to above 200 degrees.

Product Features

  • Bit Diameter: 0.4 mm – Bit length: 16 mm
  • Length of Shank: 20 mm
  • Package Included: 5 x 0.4 mm Drill Bits
  • 12-month warranty and 24*7 customer support with technical advice
  • ★Don’t use the drill to clean until the nozzle is heated to above 200 degrees

Click Here If You Need More Detailed Info…

3D Printer M7 thread MK10 Nozzle Cleaning Kit 1.75MM filament .2mm .3mm .4mm .5mm .6mm .8mm 1.0mm Nozzles and De-clogging Bits + 3.5″ Pin-vise Poor Print Quality Solution

Kit includes: Nozzles/Bits/Pin-Vise

1) MK10 Nozzle for 1.75MM
Material: Brass
Filament inlet: 1.75mm
Fit for: Wanhao Dupicator D4/I3/Dremel and various Makerbot 3D Printers

Please verify that these are the nozzle for you printer. M7 thread MK10

(1 each)

.2mm

.3mm

.4mm

.5mm

.6mm

.8mm

1.0mm

2) Custom bit holding Pin-Vise

Fits 2.0mm and 3.75mm shank bits

3) Nozzle clearing drill bits:

(2 each) 0.2mm 0.3mm 0.4mm

(1each) 0.5mm 0.6mm 0.8mm 1.0mm

Cleaning Information:

These drill bits are of the highest quality you can find but are delicate by nature. Only with the bits can you clear clogs and clean out nozzles of any size. We have bits of larger sizes if you should need them.

The delicate nature of the bits means you must be very careful when using them. Do NOT apply side pressure. North/South movements only. You can clear a cold nozzle if done carefully, but it is HIGHLY recommended that you heat the nozzle first. You can leave it on the printer, or take it off. You can even heat it with a blow-torch after removing, but that will blacken the nozzle. Regardless, the nozzle should be fastened or clamped down if removed to avoid movement. Once you get the nozzle firmly set, use the pin-vise to insert the bit slowly. Spin the bit a few rotations and slowly pull it out. The nature of the bit curves will pull out any clogs and you are back in business!!

Product Features

  • Will clear nozzles and produce finer prints
  • Shipped in protective plastic case
  • M7 thread MK10 printer nozzles .2mm .3mm .4mm .5mm .6mm .8mm 1.0mm
  • De-clogging bits (2 each) .2mm .3mm .4mm (1 each) .5mm .6mm .8mm 1.0mm
  • 3.5″ comfortably held nozzle cleaning pin-vise tool

Click Here If You Need More Detailed Info…

3d Printer Nozzle Cleaning, 10PCS 0.4MM Drill Bits for 3D MakerBot Printer Nozzle Cleaning Kit by EAONE


EAONE 10PCS 0.4MM Drill Bits for 3D MakerBot Printer Nozzle Cleaning Kit

Specification
Type:drill bit
Material: silicone
Bit diameter: 0.4mm
The length of drill: 8mm
The length of shank: 20mm
Color: Random

Don’t use the drill to clean until the nozzle is heated to above 200 degrees

Package include
10 x Drill bits

Product Features

  • Conveniently colored silicone grip gasket for spinning bits by hand
  • Diameter: 0.4mm; The length of drill:8mm; The length of shank: 20mm
  • Color: Random
  • Package includes 10 pack of 0.4mm drill bits
  • Don’t use the drill to clean until the nozzle is heated to above 200 degrees

Detailed Information available on our Homepage…

0.4mm Drill Bits – 3D Printer Nozzle Cleaning Kit – Stainless Steel, 4.1″ Length (5-Pack)

Package Included: 5 x 0.4mm Needle Drill Bits.

Product Features

  • Compatible with most well known 3D Printers on the market (e.g. Duplicator, MakerBot, RepRap etc.)
  • Bit diameter: 0.4mm; The bit length:7.5cm; The length of shank: 3cm; Total length: 10.5cm. Material: Stainless Steel.
  • Good toughness and not easy to break off.
  • Package Included: 5 x 0.4mm Needle Drill Bits.
  • 30 DAY MONEY BACK GUARANTEE – All PAGOW customers enjoy 30 Day Money Back Guarantee. Customers can return and get refunded in case the purchasing is not satisfied for any reason.

Click Here If You Need More Detailed Info…