Professional 3D printer CNC Kit for arduino, kuman GRBL CNC Shield +UNO R3 Board + RAMPS 1.4 Mechanical Switch Endstop + DRV8825 A4988 GRBL Stepper Motor Driver with heat sink + Nema 17 Stepper Motor

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware)

Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles
Length of Cable: 70 cm

Package Contents:
1 x CNC Shield Board
1 x Kuman UNO R3 Board
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
12x M3 Screws for bracket of stepper motor
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
1 x 1.5m USB cable for R3 Board

Product Features

  • Latest CH340G CNC Shield expansion board Version 3.0 for Arduino
  • Kuman UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable
  • 4pcs DRV8825 Stepper Motor Driver with heat sinks
  • 3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws
  • 3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable

Click Here If You Need More Detailed Info…

What's Hot Today!

SIM&NAT 12inch / 30cm 40 Pin Male to Female Dupont Wire, 40 Pin Male to Male, 40 Pin Female to Female Breadboard Jumper wire Ribbon Cables kit for Arduino Raspberry Pi 2 / 3 (120 PCS)


Features:
Material:Copper wire
The wires are easy to peel apart and great for making good looking prototypes
soft and flexible

Applications:
Work on a Raspberry pi breadboard projects, Raspberry pi robot build, Breadboard prototyping, Arduino and ky-040 rotary encoders.
Insert onto the SW LED pin on the typical desktop computer mother board.
Test bread boarding projects or for any breadboard experimenter.
Fit into a 3-pin JST.

Package Included:
1 * 11.8 inch 40 pin male to male Breadboard Jumper Wires
1 * 11.8 inch 40 pin female to female Breadboard Jumper Wires
1 * 11.8 inch 40 pin male to female Breadboard Jumper Wires

Product Features

  • Length: 30cm/11.8 inch
  • The pitch of each end of the wire is 0.1 inch (2.54mm)
  • 40 pin jumper Wire are easy to separate from the ribbon
  • Suitable for Arduino breadboard kit project, PCB project, PC motherboard, DIY experiment, 3D printer and etc.
  • Package content: 1 * 40 pin male to female jumper wires, 1 * 40 pin male to male cable and 1 * 40-pin female to female cable (total 120pcs)

Click Here If You Need More Detailed Info…

What's Hot Today!

Longruner GRBL CNC Shield Expansion Board V3.0 +UNO R3 Board + A4988 Stepper Motor Driver With Heatsink for Arduino Kits (Arduino Kits)

CNC Shield Board:
Latest Arduino CNC Shield Version 3.0
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC

Arduino UNO R3 Board:
MCU: ATmega328
USB interface: ATmega16U2
Operating voltage: 5V
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
I-I/O pin output current: 40mA max
3.3V output current: 150mA max
Flash memory: 32 kB (0.5kB used by bootloader – included)
Static RAM (SRAM): 2 kB
EEPROM: 1 kB
Clock speed: 16MHz

A4988 Stepper Motor Driver:
A4988 Stepper Motor Driver Board is a breakout board for Allegro’s A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection;

Low RDS (On) Output :
Automatic current decay mode detection / selection
Mix with slow current decay modes
Synchronous rectification for low power dissipation
Internal UVLO
Crossover-current protection
3.3 and 5 V compatible logic supply
Thermal shutdown circuitry
Ground fault protection
Load short-circuit protection
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble).

Package Contents:
1 x CNC Shield Board
1 x UNO R3 Board for Arduino
4 x A4988 Stepper Motor Driver
4 x Heat Sink

Product Features

  • Latest CNC Shield Version 3.0 for Arduino.
  • Arduino UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2.
  • PWM Spindle and direction pins. 4-Axis support. Runs on 12-36V DC.
  • 2 x End stops for each axis (6 in total).
  • 4Pcs A4988 Stepper Motor Driver with radiator.

Click Here If You Need More Detailed Info…

What's Hot Today!

For Arduino Professional 3D printer CNC Kit,Longruner GRBL CNC Shield +UNO R3 Board+RAMPS 1.4 Mechanical Switch Endstop+DRV8825 A4988 GRBL Stepper Motor Driver with heat sink+Nema 17 Stepper Motor

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino.
GRBL 0.9 compatible.
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13).
2 x End stops for each axis (6 in total).
Coolant enable.
Compatible with A4988 or DRV8825 stepper driver.
Runs on 12-36V DC.

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware).

Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection Description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles.
Length of Cable: 70 cm

Great Package Includes:
1 x CNC Shield Board
1 x Longruner UNO R3 Board
1 x 1.5m USB cable for R3 Board
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
12x M3 Screws for bracket of stepper motor

Product Features

  • Latest CH340G CNC Shield expansion board Version 3.0 for Arduino.
  • Longruner UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable.
  • 4pcs DRV8825 Stepper Motor Driver with Heat Sinks.
  • 3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with Mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12pcs M3 Screws.
  • 3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable.

Click Here If You Need More Detailed Info…

What's Hot Today!