MK2B Heated Bed, NTC 3950 Thermistor & Borosilicate Glass Combo

Complete set: 214mm x 214mm MK2B with soldered thermistor, soldered power cord and 214mm x 200mm borosilicate glass plate.

Product Features

  • MK2B: 214mm x 214 mm (8.4 in x 8.4 in) 12V or 24V Heated Bed for MakerBot RepRap UP Mendel I3 Printer
  • Thermistor included: 100K ohm NTC 3950, soldered and installed
  • Borodilicate Glass: 3mm thick, 214mm x 200mm, will not interfere with MK2B mounting screws
  • Soldered power leads
  • Red soldermask and white silkscreen on both sides

Visit The Website For More Information…

Anycubic NTC 3950 100K Thermistor with 1 Meter Wiring and Female Pin Head for RepRap 3D Printer Heatbed or Hot End Pack of 5PCS

Specification:

– For 3D printers: use TEMP_SENSOR 11 in Marlin firmware

– Small Size: 1.25mmx2.0mm glass bead

– High accuracy: 1%

– Resistance value at 25°C=100K

– Wiring insulation: high temperature teflon/PTFE

– Wiring length: 1 meter

Package List:

5* NTC 3950 100k thermistor with female head

Product Features

  • Conviniently pre-wired with 1 meter long high temperature PTFE insulated wiring
  • Use it with heated bed or extruder
  • Temperature sensor 100KΩ accuracy of ± 1%
  • Pack of 5PCS

Click Here For More Information

TOOTO 3 PCS 100Kohm NTC 3950 Thermistors with Teflon Insulated Wiring for RepRap Prusa 3D Printer Extruder or Heated Bed pre-wired


Lot of 3 pcs NTC 3950 thermistors. Thermistors have been pre-wired for your convenience with 1 meter teflon insulated wires.

NTC 3950 Thermistor features:

– For 3D printers: use TEMP_SENSOR 11 in Marlin firmware
– Small Size: 1.25mmx2.0mm glass bead
– High accuracy: 1%
– Resistance value at 25¡ãC=100K
– Wiring insulation: high temperature teflon/PTFE
– Wiring length: 1 meter

Package contents:

– 3 x NTC 3950 100k Thermistor assembled with 1 meter teflon wiring.

Product Features

  • Support for NTC 3950 is included in Marlin firmware, use TEMP_SENSOR 11 in firmware configuration
  • Conviniently pre-wired with 1 meter long high temperature teflon insulated wiring
  • Use it with heated bed or extruder
  • Cable length :1m
  • Temperature sensor 100K¦¸ accuracy of ¡À 1%

Detailed Information available on our Homepage…

Metal DIY Hot End for RepRap 3D Printer 1.75mm Filament, 0.4mm Nozzle, 12V 40W Heater, NTC 3950 Thermistor Hotend

12V version with 40W heater. DIY hotend requires heat sink to operate properly – metal base, aluminum block, or any other type of cooling device.

Assembly of this device is straight forward. Please consult with supplied drawings and pictures for visual clue. Suggested way of thermistor mounting: JB Weld steel epoxy or kapton tape.

DIY Hotend features:

– 26mm long stainless PTFE lined barrel, for low friction, trouble free print.
– Nozzle is based on MK8 makerbot nozzle geometry and can be exchanged or replaced with many different types of nozzles on the market. This will give you good selection of nozzle orifice diameters.
– Low profile: only about 39 mm high.
– NTC 3950 100K pre-wired thermistor.

NTC 3950 Thermistor parameters:

– Small Size: 1.25mmx2.0mm glass bead
– High accuracy: 1%
– Resistance value at 25C=100K
– Wiring insulation: high temperature teflon/PTFE
– Wiring length: 1 meter

Package Contents:

1 x MK8 Nozzle 0.4mm extrusion diameter.
1 x Stainless PTFE lined barrel.
1 x Aluminum heater block with one M3x3 setscrew.
1 x 12V 40W Cartridge Heater.
1 x NTC 3950 Pre-wired thermistor

Product Features

  • Stainless PTFE lined barrel for trouble free, low friction print
  • Pre-wired NTC3950 thermistor
  • Low profile design – height is only 39mmm
  • Use it with heatsink or cooled metal base
  • Plenty of MK8 clone nozzles compatible with this hotend – nozzle replacement is cheap and easy

Check Out Our Website For Details…