OSOYOO MKS Base V1.4 3D Printer kit with MKS Base V1.4 Controller board + 2.8″ TFT LCD Touch Screen

1) If your computer can’t recognize the MKS Base 1.4 controller board, Please download and install the FT232 driver in your computer: www.osoyoo.com/driver/ftdi_ft232_drive.exe. If the driver we provide doesn’t work with your computer, please google the “FT232”
2) If you cannot get the Z-axis to move or move in right direction, Pls read carefully about Marlin firmware installation guid and learn more about the setup for Z-axis: http://www.osoyoo.com/?p=1399

Specification for MKS BASS V1.4 3D printer board:
suitable for dual-Extrude printer
3x temperature ADC connectors for thermistors
4x PWM capable power mosfet outputs with voltage selector for MainPower.(Bed, Extruder0, Extruder1, Fans)
6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax
Support 12V-24V power input. the Max working currency is 15A.
It can accept 24V input. With the same power input, the MKS BASS V1.4 board can reduced the current of hotbed to 1/4 than ramps1.4, so it solve the MOS hotbed overheat problems.
The size of the board: 11×9(cm)

Specifications for 2.8 Inch Full Color LCD Touch Screen:
2.8 inch colorful touch screen LCD
Support U disk and SD card.
Support continual and easy software update.
Suitable for many main board such as Ramps1.4 and MKS Base V1.2 update version, MKS Gen, MKS Mini.
Support Marlin, Smoothieware and Repetier.
Support MKS Wifi module.

Package include:
1x MKS Base V1.4 Board
1x USB Cable
1 x 2.8 Inch Touch Screen (SD card not included) 1x Flat cable

Product Features

  • We have full tech support to assist you with MKS BASS V1.4 3D printer board, For more details and Marlin firmware installation guide, Pls go to the web: http://www.osoyoo.com/?p=1399
  • This MKS BASS V1.4 board is with simple interface as it is the combination of Arduino MEGA2560 + RAMPS1.4 + 5 x A4982 drivers. 4 layers PCB design of MKS BASS V1.4 board optimize heat dissipation. A4982 drivers is SOP on MKS BASS V1.4 board, and it is better heat dissipation than A4988 driver. This MKS BASS V1.4 board can be recoverable fuse for short-circuit protection
  • With the MKS Base V1.4 3D Printer kit, you can easy to control your 3D printer device. Firstly, 2.8 Inch Full Color LCD Touch Screen With a SD card slot and USB Disk Solot on back, put slicing file into the SD card and select the file on the LCD, then can be printing. Secondly, MKS BASS V1.4 board with the RepRapDiscount SmartController compatible pin header on board. It can connect 12864LCD directly
  • 2.8 Inch Full Color LCD Touch Screen doesn’t need additional 12V additional power when connecting with MKS Base V1.4,
  • 2.8 Inch Full Color LCD Touch Screen Support keep printing and saving outage function. Using this function, you should choose Pause action first before you breakout the power. When you open the power again, the printer can run from the situation before you breakout the power

Click Here If You Need More Detailed Info…

What's Hot Today!

Published by


3D Printing. The next Goldrush is on it´s way. Inside information on how to start printing in 3D, where to buy Printers, how to use them, and the newest Pictures and reviews of available 3D Printers.

3 thoughts on “OSOYOO MKS Base V1.4 3D Printer kit with MKS Base V1.4 Controller board + 2.8″ TFT LCD Touch Screen”

  1. Works great for my Hictop Prusa I3 3D desktop printer I bought this to replace my board that came with my hictop prusa I3 3D printer, , I broke my original board adjusting the current to the stepper motor and this one is so much better my old one would stop the print job in the middle of a print due to overheating. I ran a 15 hours print job with this and it worked great. There is no firmware…

  2. Great buy! I purchased this after my ROBO 3D R1 Plus failed on me. Their support did provide me with a replacement RAMPS shield, which failed shortly after I got it. Figured I’d try this one, as it looks similar to the board used in my old Prusa Mendel i3, and I’ve just finished installing it. For those interested in this project, I did need to drill new mounting holes (including one in the front bottom of the case to allow for the USB cable) but it is currently printing just fine.Robo 3D’s…

Leave a Reply

Your email address will not be published. Required fields are marked *

Enter Captcha Here : *

Reload Image