Gowoops 3D Printer Motherboard MKS MINI V1.2 RepRap + 2.8 Inch Full Color Touch Screen LCD MKS TFT28 V1.2

MKS MINI V1.2 Board User Manual: http://osoyoo.com/2016/09/21/mks-mini-v1-2-3d-printer-board-circuit-connection-graph-and-firmware-installation-guide/

MKS-TFT28 Touch Screen User Manual: http://osoyoo.com/2016/07/25/mks-tft-2-8-touch-screen/

1) Do not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can remove static charge by touching metal tap) .
2) Always double check power wire is properly installed. If you do not follow above move, you can damage the control board and your 3D printer.

MKS MINI V1.2 printing integrated mainboard:

MKS MINI is a feature all-in-one electronics solution for Reprap and other CNC devices.
It features an onboard ATmega2560.
It’s four motor outputs are powered by DRV8825 stepper drivers.
The board can use the same firmware as Ramps1.4.
The mounting hole locations is the same as Arduino Mega2560.
The power supply with 7805, more stable and reliable than the 1117, but only supports 12V.USB to serial modules is 16U2, the same as Arduino Mega2560.Without hot bed heating output, but has bed thermal interface and bed control signal interface.

MKS-MINI is suitable for One-Extruder and no bed printing.

LCD Full Color Touch Screen MKS TFT28 V1.2
Set the Boot
1) Must: After the first boot into -> Settings -> connection, select the firmware used by the baud rate, it can be used.
2) You must: Go to -> Settings -> type, select the printer type, only Delta and the other two options.
3) Optional: You can enter -> Settings -> touch screen calibration, improve the accuracy of the touch screen.

Package Included:
1 x 2.8 Inch Full Color Touch Screen MKS TFT28 V1.1 For 3D Printer
1x MKS MINI V1.2 Board

Product Features

  • MKS MINI V1.2 Board: Arduino MEGA compatible Atmega2560 processors are compatible with all RAMPS class firmware. Easy DISPLAY + SD-CARD connector, RepRapDiscount. SmartController compatible pin header on board. Firmware can use the same configuration as ramps1.4.
  • MKS MINI V1.2 Board: 2x temperature ADC connectors for thermistors, up to 4 motor driver with DRV8825. 2x PWM capable power mosfet outputs with voltage selector for MainPower.(Extruder0,Fans). 6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax. 4 layers PCB, optimize heat dissipation. Recoverable fuse for short-circuit protection.
  • MKS-TFT28 is an independent color touch product suitable for the use of open source 3D printers, support U disk and SD card. The main control program without need modification, plug and play, support Marlin, Repetier, Smoothieware firmware.
  • MKS-TFT28 support power failure renew,power failure preservation. The main control program without need modification, plug and pla. Can increase the custom function button. Provide continuous software upgrade, upgrade method is simple.
  • MKS-TFT28 can be used on Ramps1.4 and MKS Base , MKS Gen , MKS Mini and a series of motherboard. Boot logo and all buttons, such as interface can be designed by ourselves.

Visit The Website For More Information…

What's Hot Today!

Published by


3D Printing. The next Goldrush is on it´s way. Inside information on how to start printing in 3D, where to buy Printers, how to use them, and the newest Pictures and reviews of available 3D Printers.

One thought on “Gowoops 3D Printer Motherboard MKS MINI V1.2 RepRap + 2.8 Inch Full Color Touch Screen LCD MKS TFT28 V1.2”

Leave a Reply

Your email address will not be published. Required fields are marked *

Enter Captcha Here : *

Reload Image